How do I use the VOLCANO? Please refer to the or . The VOLCANO is turned on by activating the red switch. It is allowed to preheat 3-5 minutes. The material is put into the Filling Chamber and placed on top of the VOLCANO. The Valve Balloon is attached and the green switch is activated. The Balloon fills with vapor in 30 seconds to 1 minute, and once filled, the green switch is pressed again. The Filling Chamber is disconnected from the Valve Balloon and removed from the VOLCANO. The Mouthpiece is attached to the Balloon and the vapor is applied. What are the uses of the VOLCANO? Is the VOLCANO easy to use? The VOLCANO is very easy to use. The simple design allows a novice to become an expert in no time. Most users master the system in less than 10 minutes. There is manufacturer support, so if you do have questions, you can get them answered quickly. Checkout the  to see how easy it is. What determines the vapor quality in the Balloon? The proportion of aroma, flavor and material are the key to the vapor quality in your Balloon.

It is best to use quality material in limited quantity in the VOLCANO to achieve best results. Pay attention to how well the material is ground. You can optimize the amount of vapor released into your Balloon. Pay close attention to the following factors: Quality: The concentration of ingredients in the material. Quantity: The amount of material in the Filling Chamber. Surface Area: The finer the material is ground, the greater the surface area and the more vapor can be released. Temperature: The higher the temperature, the more vapor will be released at once. Use only the optimal vaporization temperature for your material. Be careful with increasing your temperature too much too soon. Excessively high temperature could make your material taste and smell more roasted. Can the VOLCANO burn what you put into it? What is the best temperature setting? Because of the many applications and broad range of user preferences, there are many appropriate temperature settings.

Use the plant list in the  as your reference. Select your temperature as low as possible to start to avoid over roasting you material. Incrementally turn your setting up or down dependent on your preference. You can easily determine the appropriate temperature setting by observing the vapor generated in your Valve Balloon. The setting is perfect when a fine white mist is seen. If you see vapor which is barely visible, you will know that either the temperature is too low or the material vaporised is exploited. oreck air purifier collector cell light blinkingThick and very dense vapor may be unpleasant to apply.hyla tadpole air purifier The VOLCANO ensures that the ingredients of a material are released gently in the Balloon. honeywell true hepa allergen remover tower air purifier cadr

This allows you to repeat your vaporization with the same material in the Filling Chamber. You can reuse the material in the Filling Chamber several times until all of the flavor and aroma is completely released. The flavor has little to do with the effect. Flavor inducers such as volatile essential oils vaporize much quicker than other ingredients. The initial flavor vanishes after the first few procedures, but the effect is undiminished. Flavor always depends on what you put in your Vaporizer. The Vaporizer does not influence the flavor in any way. Why is there no vapor when I first fill the Balloon? Refer to the . There are two factors: the Filling Chamber and the vaporized material. The Filling Chamber Cylinder has to reach the vaporization temperature before the material can be vaporized. The vaporized material will contain ingredients other than flavor and aroma, such as water vapor (humidity). To avoid filling your Balloon with cold air or water vapor, you can preheat the filling chamber by setting the Filling Chamber on the hot air outlet of your VOLCANO without the Valve Balloon attached.

Press the green AIR switch and allow hot air to warm up your material for a few seconds before placing the Valve Balloon on the Filling Chamber. This ensures that the Balloon is completely filled with flavor and aroma from the very beginning. How long can the vapors be stored in the Balloon? How often do I need to change my Balloon? How do I remove/attach the Balloon?To change the SOLID VALVE Balloon, remove the Slipring. Older models may still have the Balloon Clip: remove the Clip (the part with teeth) by sliding the male teeth up and female teeth down (do not try to force the Balloon Clip open by pulling the teeth against each other). Remove the old Balloon from the Valve. Cut a length of new Balloon Material from the roll and tie off the end. Attach the new Balloon with the Balloon Fixation Ring and attach the Balloon Clip / Slipring for a tight seal. For the EASY VALVE, simply take the new Balloon out of the box and you are ready to go. How big can I make the Balloon?

How often do I need to clean my spare parts? How do I disassemble my spare parts?Place your spare parts into a dish of hot water and let them soak for 5 minutes. Completely disassemble your parts to make sure all residue can be removed. Sometimes it is necessary to use a screwdriver or pliers to separate really dirty parts. How do I clean my spare parts?You may use rubbing alcohol or automatic dishwasher. What is the Liquid Pad used for? Which parts of the VOLCANO Vaporizer are subject to wear and tear? Replace the SOLID VALVE Balloon when it becomes dirty. It is best to replace the SOLID VALVE Balloon in regular intervals (after 50 – 100 uses). Replace the Balloon after cleaning your Valve Set. The SOLID VALVE comes with a 10 feet/3 meters roll of bulk Balloon Material. It is sufficient for 3 – 5 Balloons. You may also use other heat resistant oven bags. Please do not use any other plastic bags or clingwraps as these materials are not heat safe and may damage your parts.