The Vic Shop added 3 new photos.Easiest power we've made all week! This Judge came in with Vic pipes and the customer wanted the RPW USA - Rogue Pipe Works Big Slash installed. No other mods, just a Lloydz Motorworks VFC controller to make it run safe and BAM!, huge power and torque increases throughout the range. :)The Vic Shop added 3 new photos.The Vic Shop is where you go for Victory Performance! We stock wide array of popular parts that will improve your enjoyment of your ride. The Fall Season is upon us and we're all stocked up and ready to go. We work 100% by appointment so send us a Message, a phone call, or an e-mail and we'll get you scheduled for that performance injection you've been dreaming about!The Vic Shop added 2 new photos.A couple of nice cruisers came in today. The 2006 Vegas received a cam transplant along with a dyno tune. The Highball got a new set of pipes, intake and fuel controller. Details in the pictures..The Vic ShopHere is another 2004 model that we modified to accept new Bassani Xhaust.

Awesome look and sound!And here is the opposite result of the bike we posted on Wednesday. Where the last bike was all about big midrange torque, this bike is all out the high-end power. Actually we had our reservations about combining the Conquest Customs Ground Pounder pipes and the Lloydz Motorworks DR-T cam knowing that both favor the high end of the rpm scale. bionaire permatech air cleanerOur minds were put to ease when the customer complained about always hitting the rev limiter on the stock bike. holmes aer1 ready air purifierWell if you ride like that, you're going to love this combination! quietflo true hepa air purifierCould you imagine going from a stock bike (red lines) to this loud and proud, high revving beast?!

Blue lines reflect the results after the work. Now this bike has the look, sound, and performance the customer needed!A cam and pipe for Torque! Customer wanted to pump up his stock 106" Hammer. He had chosen the Freedom Performance Exhaust Inc Slash pipes which we've known to be great low-to-mid range power producers. So we suggested the WYRD Brothers XV30 cams to complement the pipes. These cams also make great low-mid range power. Together with a Torque Tube intake, timing wheel, and dyno tune the Hammer now has gobs of usable torque to spin that fat back tire! These runs were taken in 4th gear, 5th gear pulls saw over 120 ft/lbs at a measly 3500 rpms!The Vic Shop added 2 new photos.2004 Kingpin before and after a Bassani Xhaust install. Our customer was frustrated with a lack of exhausts that fit his 2004. "well you know we can modify any 106" model exhaust to work on your 2004" we told him. With his options wide open he picked this Bassani 2-1. The great sound, power, look, and build quality of the Bassani really adds to the appeal of his super clean Kingpin!

The Vic Shop added 4 new photos.Another black bike passes through the shop. We dyno'd the bike when it come in (blue lines) for a baseline. We then removed the Stg1 pipes, S&S airbox and VFC tuner and replaced with Conquest Customs Octane exhaust, Lloydz Motorworks Torque Tube intake and VM1 cams, and a Power Commander for fuel control. The customer couldn't resist the look of the MSD coils so we threw them on too. Last piece of the puzzle was adding some baffles to the pipes, tune it all up on the dyno and send it back home. It turned heads at every stop sign and gas station all the way home according to the customer!The Vic ShopThis morning she said "I don't want to go to pre-school, I want to stay at the shop" and I've never felt so conflicted. -Rylan-The Vic ShopCustomer: "The closest tuner I could find was in Dallas, which is 7 hours away. The Vic Shop was just a few more hours on top of that, so might as well have you guys do it!"Another Black Beauty rolls through the shop. A couple of years ago we had done the "Cam Job" on this bike.

This time around we performed the 30K service then retuned the bike for the TriOval pipes that the customer had swapped to. I love it when a clean, sharp, well maintained bike comes in for performance work. This Vegas passed through the shop the other day.The Vic ShopWe found out why the throttle was sticking on this Vision. A mouse had used the throttle body as a toilet. The part had to be removed and bead-blasted to clean it up. The Vic Shop added 2 new photos.116" Cross Country. Lloydz Motorworks cylinders/pistons/DR-Tcams/intake/timing wheel and heads. Built and tuned by The Vic Shop.The Vic ShopThings are starting to look real down at The Vic Shop 2.0 build site!The Vic Shop"Hey Gabe, it's the weekend, lets knock off early and get some ice cream! I'll take the Octane, you hop on the Vision." -Rylan-Posted by The Vic Shop50K Service. Grease the steering head bearings, replace the fork oil, replace the fuel filter, we rebuilt the starter to remedy the "goose squawk" it had developed.

Plugs, cables, brakes, oil, suspension, etc, etc. With the two of us banging it out quickly in the morning, I think we have time to add a bunch of power with The Cam Job in the afternoon! It'll be like a new bike.... well...better than new! :)The Vic ShopWe're back in the saddle again and looking to fill up our August schedule! We almost had a cam job scheduled for every day left in August, until this morning when my Wednesday appointment had to cancel. So anyone looking for a last-minute cam job on their Vic? For two days from now? We also have Tuesday the 30th open in order to fill up this month. The Vic ShopOh, yeah! We found the right road! :)The Vic ShopWe're getting cleaned up and headed West like so many folks do this time of year. But we're not Sturgis bound, it's off to Colorado for the VMC National Meet! Inside the trailer in the background is The Vic Shop's Vision and the Wheels For Warriors bike. In the foreground The Vic Shop's new Cross Country project bike gets a bath before taking the third spot in the trailer.